Configure Ethernet Connection Manually on Windows 10

The Ethernet settings page appears. 4Click Change Adapter Options. The Network Connections page appears. This page lists each of your network adapters.

After running the Hardware Setup steps of the installer, if the radio is still not detected, you can attempt to configure the network interface manually via the Windows Network Connections App or the command prompt.

Configure Ethernet Connection Via Windows Network Connections App

  1. Open the Control Panel from the Windows® icon in the lower left corner of your monitor.

    In the Control Panel window, make sure View by is set to Category.

  2. Click Network and Internet.

    Jim L., USA“We have been using CDFinder and NeoFinder for almost 17 years, now. It is a great product that has consistently proven itself to be extremely useful to us over the years. Without a doubt, it is one of the best software investments I have ever made.' 'An amazing piece of software.as a photographer I have tons of files to track.' Neofinder mac photos. Don G., Illinois, USA“Since we started cataloging our binders full of CDs/DVDs of images, we now have over 700 catalogs of CDs, mainly DVDs of our collection.

  3. Click Network and Sharing Center.

  4. Click Change adapter settings in the left pane.

  5. Sort the adapters by clicking the More options button, and then selecting Details. Double-click the adapter to configure to open its properties.

    On this computer, the adapter with the name Ethernet indicates connectivity to the Internet, but the connectivity of Ethernet 2 indicates No network access. Double-click the Ethernet 2 adapter to open its properties.

  6. On the Networking tab, clear Clients for Microsoft Networks and File and Printer Sharing for Microsoft Networks. These services can cause intermittent connection problems with USRP® radios. To configure the IP address, double-click Internet Protocol Version 4 (TCP/IPv4).

  7. On the General tab, the default setting is typically set to Obtain an IP address automatically.

    Select Use the following IP Address. Set the host IP address to 192.168.10.X, where X is any integer from 1 to 255 except 2. Leave the Subnet mask set to its default (255.255.255.0).

    If your radio is on another subnet, meaning the first three octets of the IP address field are not 192.168.30, then enter the IP address values of your radio for the first three octets. See Check Subnet Values on Host and Radio.

  8. Click .

  9. The host computer configuration is complete. Continue to Verify Hardware Connection.

Configure Ethernet Connection Via Windows Command Prompt

Use these commands to determine the IP address of the radio. After determining the IP address for the radio, update the network interface IP address, and ping the radio to verify that the host-to-radio connection is working.

  1. View the list of network interfaces, by entering this command at the Windows command prompt.

    For the host computer used in this example, this is the output.

  2. Determine which Ethernet adapter is used for the internet connection by pinging the IP address associated with each Connection Name returned. When you identify the connection name of the network adapter connected to the Internet, avoid selecting that network adapter for the radio. For more information, see Host Computer Ethernet Options.

    The host computer in this example uses the 'Ethernet' connection name for the Internet connection. Run the netsh command with this syntax to get the IP address of 'Ethernet'. Then ping that IP address to a website. Since the host computer uses this network adapter for its internet connection, reconfiguring this adapter to connect to the radio would jeopardize your ability to connect to the Internet. See Using One Ethernet Port.

  3. Next we run the netsh command specifying the 'Ethernet 2' connection name. DHCP is typically enabled for an adapter that is not statically configured. Since the host computer does not use this network adapter for its internet connection, reconfiguring this adapter to connect to the radio, does not jeopardize your ability to connect to the Internet. That makes it a good adapter to use for the host-to-radio connection.

  4. Connect the radio to this USB-Ethernet adapter. Wait for a few seconds, and then check the setting again. The response for a successful host-to-radio connection resembles the output shown here.

    The IP address 169.254.55.226 is a private IP address automatically assigned by Windows to the Ethernet adapter. To discover the IP address of your radio, ping the broadcast address 169.254.255.255. This address corresponds to the subnet prefix 169.254.0.0. The response for a successful ping resembles the output shown here.

  5. Based on the discovered radio IP address 192.168.30.7, assign an IP address to the Ethernet adapter from the same subnet, such as 192.168.30.1. Use a subnet mask of 255.255.255.0.

    Keygen generator mac online. With سيريال نمبر iMazing, if you want to copy the contents of an entire album just drag the album to your computer. You may need to display them on your iOS device first after they’ve downloaded to the device. After this, you can copy them to your computer.Further, if your iPhone or iPad uses Apple’s new C format for photos. If you use the iCloud photo library and want to copy photos that are in the cloud.

Verify that the updated IP address for the Ethernet adapter.

Verify that the host computer can ping the IP address assigned to the radio.

Configure FastSendDatagramThreshold Registry Key

Ettus Research® recommends configuring the FastSendDatagramThreshold with the value 2048 (decimal). Define or reconfigure the FastSendDatagramThreshold registry key in the Windows Registry Editor under HKEY_LOCAL_MACHINESYSTEMCurrentControlSetservicesAFDParameters.

Related Topics